Boonton Power Sensor Manuel d'utilisateur télécharger pdf (Page 15)

Table 2-2. Peak Power Sensor Characteristics (con't.)

Model

Frequency Power Overload

Rise Time

Maximum SWR

Drift & Noise

Range Measurement Rating

@ 0 dBm

Peak Fast Slow

Impedance

(1)

Peak Power High Low Frequency SWR Peak Power

RF Connector Int. Trigger CW Power Bandwidth Bandwidth CW Power

(GHz) (dBm) (ns) (ns) (GHz)

DUAL DIODE PEAK POWER SENSORS

Sensors below are for use with 4400, 4500, 4400A, 4500A and 4530.

Compatible with 4530 Series internal 50 MHz calibrator.

57318 0.5 to 18 -24 to 20 1W for 1 us

< 15

(2)

< 10 us to 2 1.15 4 uW

50 Ω

(0.05 to 18) -34 to 20 200 mW (35 MHz) (350 kHz) to 16 1.28 0.4 uW

N(M) -10 to 20 to 18 1.34

(3)

57340 0.1 to 40 -24 to 20 1W for 1 us

< 15

(2)

< 10 us to 4 1.25 4 uW

50 Ω

(0.03 to 40) -34 to 20 200 mW (35 MHz) (350 kHz) to 38 1.65 0.4 uW

K(M) -10 to 20 to 40 2.00

(3)

57518 0.1 to 18 -40 to 20 1W for 1 us < 100 < 10 us to 2 1.15 50 nW

50 Ω

(0.05 to 18) -50 to 20 200 mW (6 MHz) (350 kHz) to 6 1.20 5 nW

N(M) -27 to 20 to 16 1.28

(4)

to 18 1.34

57540 0.1 to 40 -40 to 20 1W for 1 us < 100 < 10 us to 4 1.25 50 nW

50 Ω

(0.05 to 40) -50 to 20 200 mW (6 MHz) (350 kHz) to 38 1.65 5 nW

K(M) -27 to 20 to 40 2.00

(5)

NOTES: 1) Models 4400, 4500, 4400A and 4500A only.

2) Models 4531 and 4532: <20ns, (20MHz).

3) Shaping Error (Linearity Uncertainty), all levels 2.3%

4) Shaping Error (Linearity Uncertainty), all levels 4.0%

5) Shaping Error (Linearity Uncertainty), all levels 4.7%

Fre

uenc

calibration factors

(

NIST traceable

)

and other data are stored within

all the Peak Power Sensors. Linearit

calibration is

erformed b

the built-in

calibrator of the

eak

ower meter.

MODELS 4400

4500

4400A and 4500A:

All Peak Power sensors can be used with these models and calibrated with the

internal 1GHz ste

calibrator unless otherwise noted.

MODELS 4531 and 4532:

The Peak Power sensors in the lower

rou

above ma

be used with these models

and calibrated with the internal 50 MHz ste

calibrator. The sensors on the u

rou

be used if the Model 2530 1 GHz Accessor

Calibrator is used for

calibration.

A five-foot lon

sensor cable is standard. Lon

er cables are available at a hi

her

cost. Effective bandwidth is reduced with longer cables.

10 Power Sensor Manual

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 51 52

Commentaires sur ces manuels

Pas de commentaire

Boonton Power Sensor Manuel d'utilisateur Page 15

Commentaires sur ces manuels

Produits connexes et manuels pour Instruments de mesure Boonton Power Sensor